• ·       Development of 2D/3D pipework layouts based on system requirements and spatial constraints

  ·       Routing of pipe systems (chilled water, heating, process, domestic) to optimise space and maintain access

  ·       Coordination of pipework with structural, architectural, and MEP services to avoid clashes

  ·       Sizing of pipes based on flow rate, velocity, and pressure drop calculations

  ·       Selection of materials and specifications based on system type, medium, and operating conditions

  ·       Integration of supports, anchors, and expansion allowances for thermal movement

  ·       Layouts for plantrooms, risers, corridors, and distribution zones

  ·       Creation of isometric drawings and spool sheets for fabrication and installation

  ·       Compliance with project standards, building codes, and industry best practices

  ·       Review and incorporation of supplier and vendor data into final design

• Closed water system balancing (chilled & heating systems)

• PICV set up & DPCVs set up

• DRV balancing

• Pump Testing (Start up/ Duty / Standby / Closed Head Testing)

• BMS (automation) interface management

• Domestic hot water balancing

• Fault finding & trouble shooting

• ·       Evaluation of thermal expansion, contraction, and movement across pipe networks

  ·       Analysis of stress concentrations at bends, anchors, and equipment connections

  ·       Load assessment due to internal pressure, weight, and dynamic forces

  ·       Calculation of allowable stress levels based on material properties and design codes

  ·       Design and placement of supports, guides, and expansion loops to manage pipe movement

  ·       Verification of flange alignments and equipment nozzle load compliance

  ·       Simulation of operating and standby scenarios to validate system resilience

  ·       Assessment of seismic, wind, and vibration impacts where applicable

  ·       Compliance with relevant standards (EN 13480, ASME B31.3, PED, etc.)

  ·       Generation of stress reports for design approval, fabrication, and installation teams

• ·       Pressure drop calculations across pipe networks to verify pump sizing and system balance

  ·       Flow resistance analysis for valves, fittings, bends, and equipment connections

  ·       Verification of pipe velocities to prevent erosion, noise, and flow instability

  ·       Calculation of total dynamic head (TDH) for system performance validation

  ·       Static load analysis to assess pipe support and anchoring requirements

  ·       Assessment of thermal expansion and associated stress on piping systems

  ·       Verification of material suitability for pressure, temperature, and medium type

  ·       Structural load calculations for pipe racks, hangers, and suspended systems

  ·       Compliance with project specifications, local regulations, and EN/ISO standards

  Documentation of all calculations for engineering sign-off and client assurance

• ·       Development of fabrication-ready isometric drawings and spool sheets

  ·       Coordination of pipe routing for modular assembly

  ·       Logistical planning for transport, lifting, and site installation incorporated into the design

  ·       BIM-based clash detection and layout optimisation for prefabrication feasibility

  ·       Material take-offs (MTOs) and bill of materials

  ·       Integration of supports, anchors, and access considerations into offsite modules

  ·       Fabrication sequencing aligned with construction programme

  ·       Interface coordination between prefabricated elements and site

  ·       Logistical planning for transport, lifting, and site installation

  ·       Reduction of site hours, waste, and installation time through controlled offsite execution

• ·       Detailed design of high-purity and process-critical pipework systems (e.g., WFI, clean steam, process gases)

  ·       Material specification and compatibility checks for media, pressure, and temperature requirements

  ·       Isometric development for fabrication, testing, and installation

  ·       GMP-compliant routing, segregation, and support planning

  ·       Hygienic design principles including slope control, drainability, and orbital welding integration

  ·       Pressure testing, flushing, and passivation planning

  ·       Coordination of valves, instruments, and tie-ins with process equipment

  ·       Pre-construction review and verification of P&IDs and process schematics

  ·       Field engineering support during install, weld inspections, and redline updates

  ·       Support for turnover documentation (as-builts, weld logs, test packs) and validation readiness

·       Design and coordination of chilled water, condenser water, and process cooling systems

·       Support for hot/cold aisle containment strategies and thermal zone planning

·       BIM coordination and clash detection with electrical and IT infrastructure

·       Pump and valve sizing based on N+1 and 2N redundancy requirements

·       Selection of materials and insulation for thermal efficiency and fire performance

·       Modular

·       Commissionable reviews

·       Integration with BMS and control systems for flow, temperature, and pressure monitoring

Compliance with Tier standards (Uptime Institute) and ASHRAE thermal guideline

·       Coordination of piping design packages with client teams

·       Technical review of isometrics, GA drawings, and P&IDs

·       Oversight of prefabrication and on-site installation sequencing

·       Fabrication Progress monitoring & material management

·       Interface management with other trades (HVAC, electrical, structural) to resolve clashes

·       Material take-off (MTO) verifications

·       QA/QC support including weld map reviews, hydrotest planning, and inspection readiness

·       Contribution to commissioning preparation, flushing, pressure testing, and system validation

·       Daily reporting and tracking of installation milestones and resource productivity

Support for turnover documentation, redline updates, and handover compliance